Best picks

6 Best Vacuum Sealer Accessory Hoses (November 2026)

Updated on · By the Vacuum Sealer Compare team

The best vacuum sealer accessory hoses include the FoodSaver Plastic Jar Sealer for Vacuum Sealer for Mason jar sealing, the EVIL ENERGY 1/8" Silicone Vacuum Tubing Hose for 1/8 in tubing, and the EVIL ENERGY 5/32" Silicone Vacuum Tubing Hose for 5/32 in tubing.

On this page (5 sections)
  1. The best vacuum sealer hose options for different setups
  2. How to choose a vacuum sealer hose by connector fit
  3. How to match a hose with container compatibility
  4. How to use and care for an accessory hose
  5. Best vacuum sealer hose: which one should you choose?

The best vacuum sealer hose for Mason jar storage is the FoodSaver Plastic Jar Sealer, while the EVIL ENERGY hoses suit buyers who need 1/8 in or 5/32 in silicone tubing. Match the hose size and connector before ordering.

A good seal starts at the connection point. A hose that slides on loosely or has to be forced will not hold vacuum the way the accessory was intended to work.

A vacuum sealer hose can connect a machine to a jar sealer, container accessory or replacement line. One buyer may only need a short link between a sealer and a jar, while another may need a long cut to reach a container across a worktop.

The right choice depends on connector fit, the hose inner diameter and whether you need a food storage accessory or a larger shop vacuum hose. Those three points separate a jar sealer from plain tubing and from dust collection gear.

Start with the accessory you already own. A regular or wide mouth jar sealer points you to a finished kit rather than a roll of tubing.

A bare port or barbed fitting points you to a measured inner diameter before length or brand comes into view.

Think about where the work happens. Jar sealing usually happens in the kitchen with sauces, mustards and jams kept in Mason type jars.

Shop vacuum routing happens in a workshop with dust, dirt and debris, and the hose sizes are far larger.

That difference is a trade off in both directions. A kitchen jar kit gives you the right shapes and hose in one box, but it will not replace a long line for another machine.

A 10 ft roll gives you cutting room, but it leaves you to source and test the connector yourself.

If your sealer needs a new seal around the lid, compare our guide to the best vacuum sealer replacement gasket. For the heating side of the machine, see What Is a Heat Strip on a Vacuum Sealer?.

Use those pages to narrow whether the fault sits in the lid seal, the heating element or the hose path itself. Care also depends on the part, since jar sealers that are dishwasher safe still need the hose and connector checked for cracks, kinks and loose ends.

Plain silicone tubing should be cut square, seated fully and replaced when it no longer springs back or grips the fitting. In short, match the job first and the length second.

The FoodSaver kit fits Mason jar work, EVIL ENERGY fits measured 1/8 in or 5/32 in tubing needs, and larger kits belong to other tasks. That order of decisions keeps the seal reliable and the hose easy to clean and store.

Our picks at a glance

  1. 1 FoodSaver Plastic Jar Sealer for Vacuum Sealer
    Best for Mason jar sealing

    FoodSaver Plastic Jar Sealer for Vacuum Sealer

    9.7/10 our score

    See it on Amazon
  2. 2 EVIL ENERGY 1/8" Silicone Vacuum Tubing Hose
    Best for 1/8 in tubing

    EVIL ENERGY 1/8" Silicone Vacuum Tubing Hose

    9.6/10 our score

    See it on Amazon
  3. 3 EVIL ENERGY 5/32" Silicone Vacuum Tubing Hose
    Best for 5/32 in tubing

    EVIL ENERGY 5/32" Silicone Vacuum Tubing Hose

    9.4/10 our score

    See it on Amazon
  1. 4LeLuv Silicone Vacuum Pump Hose 18"

    LeLuv Silicone Vacuum Pump Hose 18"

    Best for a ready-made quick connection
    Check it
  2. 5POWERTEC 1-1/4" OD x 10 Ft. Vacuum

    POWERTEC 1-1/4" OD x 10 Ft. Vacuum

    Best for shop vacuum routing
    Check it
  3. 6Purthog 6PCS 4.9Ft ID 1/8" 5/32" 1/4"

    Purthog 6PCS 4.9Ft ID 1/8" 5/32" 1/4"

    Best for mixed-size hose repairs
    Check it

The best vacuum sealer hose options for different setups

The FoodSaver jar kit is the most direct pick for Mason jars. The EVIL ENERGY and LeLuv options are better for buyers who already know the tubing size or connector they need.

1

FoodSaver Plastic Jar Sealer for Vacuum Sealer: Best for Mason jar sealing

FoodSaver Plastic Jar Sealer for Vacuum Sealer, vacuum sealer accessory hoses
9.7/10Our score
  • Regular and wide-mouth jar sealers
  • Accessory hose included
  • Plastic construction
  • Dishwasher safe

This kit is the clearest choice when your vacuum sealer hose project involves regular or wide-mouth Mason-type jars. It includes both jar sealers and an accessory hose.

See it on Amazon

Pros

  • Covers regular and wide-mouth jars
  • Accessory hose included
  • Dishwasher safe

Cons

  • Designed for jar use rather than general replacement tubing
  • Battery-powered operation

The FoodSaver Plastic Jar Sealer for Vacuum Sealer is the strongest match for regular and wide-mouth Mason-type jars. The kit includes 1 FoodSaver wide-mouth jar sealer, 1 regular jar sealer and 1 accessory hose, so you don't need to choose between the 2 common jar-mouth sizes.

Its plastic construction keeps the accessory focused on jar sealing rather than general-purpose tubing replacement. FoodSaver describes it for sauces, mustards and jams, which makes it useful for storing those foods in compatible jars.

The kit is dishwasher safe, BPA free and environmentally safe according to its product information. Those details matter when you plan to clean the accessory after food storage, but follow the care directions for the jar and lid as well.

Choose this first if your main goal is vacuum sealing Mason-type jars. It is less suitable when you only need a length of replacement tubing with a separately measured inner diameter.

Buy it for a complete jar-sealing accessory setup, especially when you use both regular and wide-mouth jars.

FoodSaver Plastic Jar Sealer for Vacuum SealerCheck it on Amazon
2

EVIL ENERGY 1/8" Silicone Vacuum Tubing Hose: Best for 1/8 in tubing

EVIL ENERGY 1/8" Silicone Vacuum Tubing Hose, vacuum sealer accessory hoses
9.6/10Our score
  • 3 mm inner diameter
  • 9 mm outside diameter
  • 10 ft length
  • 3 mm wall thickness

The 1/8 in EVIL ENERGY hose suits setups that require a 3 mm inner diameter. Its 10 ft length gives you material to cut for a measured replacement or custom routing.

See it on Amazon

Pros

  • Clear 1/8 in size
  • 10 ft length
  • Silicone construction

Cons

  • Does not include a vacuum sealer connector
  • Application information focuses on automotive vacuum lines

The EVIL ENERGY 1/8" Silicone Vacuum Tubing Hose Line 10FT Black (3mm ID) is the best size-specific choice when your connection needs a 3 mm, or 1/8 in, inner diameter. It has a 9 mm outside diameter, 3 mm wall thickness and 10 ft length.

The length gives you room to measure and cut a replacement section rather than accepting a short line. The 3 mm wall thickness is intended to help prevent collapse under vacuum, according to the product information.

This hose is made from FDA compliant food grade pure silicone. Its stated temperature range is -40°F to 428°F, and its working pressure is 43 PSI with burst pressure of 100 PSI at high temperature and 130 PSI at room temperature.

The main trade-off is that this is tubing, not a complete vacuum sealer accessory kit. It does not include a food sealer connector, so measure the existing fitting before cutting or joining anything.

Its application information focuses on automotive vacuum lines, which makes setup confirmation especially important for food storage.

Buy it for a measured 1/8 in replacement line when you already know how it will connect.

EVIL ENERGY 1/8" Silicone Vacuum Tubing HoseCheck it on Amazon
3

EVIL ENERGY 5/32" Silicone Vacuum Tubing Hose: Best for 5/32 in tubing

EVIL ENERGY 5/32" Silicone Vacuum Tubing Hose, vacuum sealer accessory hoses
9.4/10Our score
  • 4 mm inner diameter
  • 10 mm outside diameter
  • 10 ft length
  • 3 mm wall thickness

Choose this EVIL ENERGY hose when your connector needs a 4 mm inner diameter. The 10 ft line is useful when you need more reach or several cut sections.

See it on Amazon

Pros

  • Clear 5/32 in size
  • 10 ft length
  • 3 mm wall thickness

Cons

  • Does not include a vacuum sealer connector
  • Application information focuses on automotive vacuum lines

The EVIL ENERGY 5/32" Silicone Vacuum Tubing Hose Line 10FT Black (4mm ID) suits a setup that needs a 4 mm, or 5/32 in, inner diameter. It has a 10 mm outside diameter, 3 mm wall thickness and 10 ft length.

This is the larger of the 2 EVIL ENERGY food-grade silicone tubing options in this group. Comparing the 4 mm inner diameter with your connector is more important than choosing by brand, because a hose that is too loose or too tight may not create the needed seal.

The hose is FDA compliant food grade pure silicone, with a stated working pressure of 43 PSI and burst pressure of 100 PSI at high temperature and 130 PSI at room temperature. Its temperature range is -40°F to 428°F.

As with the 1/8 in version, this product is plain tubing and does not include a vacuum sealer connector. The product information also focuses on automotive vacuum-line applications.

Use it only after confirming that the tubing and connection are appropriate for your food-storage accessory.

Buy it for 5/32 in connections when the smaller 1/8 in EVIL ENERGY hose would not match your fitting.

EVIL ENERGY 5/32" Silicone Vacuum Tubing HoseCheck it on Amazon
4

LeLuv Silicone Vacuum Pump Hose 18": Best for a ready-made quick connection

LeLuv Silicone Vacuum Pump Hose 18", vacuum sealer accessory hoses
9.2/10Our score
  • 18 in length
  • 1/4 in inner diameter
  • Pre-installed male disconnect fitting
  • Nitrile O-ring seal

The LeLuv is a short, assembled hose for setups that need an 18 in line and a pre-installed 1/4 in male disconnect fitting. Its stated size makes connector matching easier.

See it on Amazon

Pros

  • Fitting is pre-installed
  • 18 in working length
  • Flexible silicone tubing

Cons

  • Shorter than the 10 ft hoses
  • Designed around a 1/4 in connection

The LeLuv Silicone Vacuum Pump Hose 18", 1/4" Male Quick-Connect Fitting, Black is the easiest pick when you need a shorter assembled hose with a stated 1/4 in male quick-connect fitting. It measures 18 in long and has 1/4 in inner-diameter vacuum tubing.

A pre-installed male disconnect fitting saves you from selecting and attaching a separate connector. The fitting has an engineering-grade POM body and nitrile O-ring seal, and the hose is black silicone.

The reinforced silicone construction is designed to remain open under pressure without collapsing, kinking or keeping permanent bends. LeLuv also offers the hose in 12, 18, 24 and 36 in lengths, but this specific product is the 18 in version.

That short length is useful when the accessory sits close to the pump or machine. It gives you less flexibility than a 10 ft roll, so measure the distance before ordering.

The stated compatibility is with most vacuum pump accessories and tools, plus LeLuv and Eyro cylinder systems, rather than a universal promise for every food vacuum sealer.

Buy it for a ready-made 18 in hose when your setup accepts the included 1/4 in male fitting.

LeLuv Silicone Vacuum Pump Hose 18"Check it on Amazon
5

POWERTEC 1-1/4" OD x 10 Ft. Vacuum: Best for shop vacuum routing

POWERTEC 1-1/4" OD x 10 Ft. Vacuum, vacuum sealer accessory hoses
8.9/10Our score
  • 10 ft hose
  • 1 in inner diameter
  • Three pliable plastic fittings
  • 2-1/4 in to 2-1/2 in adapter

This POWERTEC kit belongs in a shop vacuum or dust collection setup, not a small food vacuum sealer. Its fittings and 10 ft hose are useful when the goal is dust routing.

See it on Amazon

Pros

  • Long 10 ft hose
  • Three fittings included
  • Made for shop vac and dust collection connections

Cons

  • Large 1 in inner diameter
  • Plastic dust-collection hose rather than a food-storage accessory

The POWERTEC 1-1/4" OD x 10 Ft. Vacuum Hose Dust Collection Kit (70356) is for shop vacuums and dust collection tools, not a typical jar-sealing accessory.

It includes a 10 ft hose with a 1 in inner diameter and 1-1/4 in outside diameter.

The kit also includes a 1 in pliable plastic hose fitting, a 1-1/2 in pliable plastic hose fitting and a 2-1/4 in to 2-1/2 in dust hose adapter. The fittings connect to the hose using left-hand internal threads.

POWERTEC describes this setup for handheld power tools, sanding, small vacuums and dust collection systems. The adapter is intended for nominal 2-1/4 in to 2-1/2 in shop vacuum ports, but port sizes can vary between manufacturers.

That makes this a poor match for a compact FoodSaver or NESCO accessory hose. It earns a place in this comparison because the word vacuum covers very different equipment, and this kit can prevent a costly size mistake when your project is actually dust collection.

Buy it for a shop vacuum hose extension, not for Mason jar or food-container sealing.

POWERTEC 1-1/4" OD x 10 Ft. VacuumCheck it on Amazon
6

Purthog 6PCS 4.9Ft ID 1/8" 5/32" 1/4": Best for mixed-size hose repairs

Purthog 6PCS 4.9Ft ID 1/8" 5/32" 1/4", vacuum sealer accessory hoses
8.6/10Our score
  • Six silicone vacuum lines
  • Six inner diameters
  • 64 nylon connectors
  • Tube cutter included

Purthog is the broadest sizing kit here, with six hose diameters, 64 nylon connectors and a tube cutter. It suits repair work when you have not yet confirmed the needed line size.

See it on Amazon

Pros

  • Six hose diameters
  • 64 connectors included
  • Tube cutter included

Cons

  • Automotive-focused kit
  • Not intended for engine coolant or engine oil

The Purthog 6PCS 4.9Ft ID 1/8" 5/32" 1/4" 5/16" 3/8" Vacuum Lines Automotive Kit is the flexible choice when you need to compare several hose sizes before committing. It includes 6 silicone vacuum lines, 64 nylon connectors and 1 V-shaped tube cutter.

The 6 inner diameters are 1/8, 5/32, 3/16, 1/4, 5/16 and 3/8 in. Each line is 4.9 ft long, so the kit gives you multiple short replacement lengths rather than one 10 ft roll.

Purthog describes the tubing as thickened silicone with a temperature range of -40°F to 428°F. It states working pressure up to 43 PSI and burst pressure of 130 PSI at room temperature.

The smooth inner wall is intended to fit the matching nylon connectors.

This kit is mainly designed for automotive vacuum lines, air and water routing, and related uses. It is not intended for engine coolant or engine oil, and the included automotive connectors do not automatically make it compatible with a food vacuum sealer.

Buy it for mixed-size repair work when you need several hose diameters and connectors in one kit.

Purthog 6PCS 4.9Ft ID 1/8" 5/32" 1/4"Check it on Amazon

How to choose a vacuum sealer hose by connector fit

Connector fit matters more than hose length. Start by identifying whether your machine or accessory takes a dedicated jar sealer connection, a male quick connect fitting or plain tubing over a port.

The FoodSaver kit is the simplest option when the accessory is a regular or wide mouth Mason type jar sealer. It includes the hose and both jar sealer shapes, so the choice is based on the jar mouth rather than a bare tubing measurement.

For jar use, set the sealer square on the lid and press the hose connection home before you start the machine. A half seated hose is a common cause of a weak vacuum, even when the jar and lid look fine.

Check the hose end for nicks or flattening after storage, since a small fault there can let air leak past the seal. For replacement tubing, compare inner diameter first.

The EVIL ENERGY choices are 1/8 in and 5/32 in, while Purthog includes those sizes plus 3/16, 1/4, 5/16 and 3/8 in. Inner diameter is the opening that must grip the fitting, so it decides fit before outside diameter or length are considered.

A larger outside diameter does not mean the hose will fit your connector. Outside diameter affects how the hose sits in a clamp or passes through a guide, but the seal forms on the inside.

The LeLuv hose is different because its 1/4 in male quick connect fitting is already installed. It may be the better choice when your equipment uses that fitting and you want an 18 in finished hose instead of a roll to cut.

Short finished hoses suit close setups where the accessory sits near the machine. They are easier to route, easier to clean and less likely to loop or catch on a counter edge.

The trade off is reach, so measure the distance with the jar or container in its normal working position before you choose 18 in over a longer option. Plain tubing suits repair work where the connector is already known and sound.

You can cut a section to length, test the fit by hand and trim a small amount if the end is damaged. When you compare kits, count what is actually included, since a jar kit brings both sealers and a hose, Purthog brings six diameters with connectors and a cutter, and a single roll brings length without a sealer connector.

How to match a hose with container compatibility

Container compatibility comes from the accessory and connector combination, not from the word vacuum alone. A Mason jar sealer, a vacuum storage container and a shop vacuum can all use air pressure, but their ports and intended uses differ.

For jars, choose the FoodSaver kit when regular and wide-mouth Mason-type jars are your target. For other containers, confirm the container port and accessory connection before choosing plain silicone tubing.

A hose described for automotive vacuum lines should not be treated as a universal food-storage hose. The EVIL ENERGY products identify FDA compliant food grade pure silicone, but their application information focuses on automotive vacuum lines.

Purthog is also automotive-focused and says it is not intended for engine coolant or engine oil.

If you use a FoodSaver machine, our guide to the best FoodSaver replacement gaskets can help when the problem is a worn lid seal rather than a hose. NESCO owners can compare the best NESCO vacuum sealer accessories before adapting a connector.

How to use and care for an accessory hose

Measure the route before cutting a hose. Leave enough length for the machine and container to sit in a comfortable position, but avoid loose loops that can catch on the counter or pull on a connector.

Inspect the hose ends after cutting. A rough or angled cut can make it harder to seat tubing evenly, while a fitting that is not fully inserted can allow air loss during the vacuum cycle.

Keep the hose clean and dry according to the accessory's care directions. The FoodSaver jar sealers are dishwasher safe, but that does not mean every hose, connector or jar lid should go through the same cleaning process.

Replace tubing when it develops cracks, permanent kinks or a loose connection. If the machine still struggles after the hose looks sound, check the gasket and the lid seal before assuming the pump has failed.

For safe storage, use the right container for the food and clean parts that touch food. Vacuum sealing changes the air around food, but it does not replace normal refrigeration, freezing or safe handling.

Best vacuum sealer hose: which one should you choose?

The FoodSaver Plastic Jar Sealer is the best vacuum sealer hose choice for regular and wide mouth Mason type jars because it includes both sealers and an accessory hose. Choose the EVIL ENERGY 1/8 in hose for a measured 3 mm connection, or the 5/32 in version for a 4 mm connection.

Pick the LeLuv when you need an 18 in hose with a pre installed 1/4 in male quick connect fitting. Choose Purthog when several automotive hose sizes and connectors are more useful than a finished food storage accessory.

The POWERTEC kit belongs with shop vacuum and dust collection tools. Its 1 in inner diameter and 10 ft length show why it sits in a different class from jar accessories.

Before ordering any replacement hose, match inner diameter, connector style, length and intended use to the machine or container you already have. Write those four points down and check them against the product details before you cut anything.

For Mason jar work, confirm the jar mouth first. Regular and wide mouth sealers are not interchangeable, so the kit that includes both removes a common source of doubt.

Store the sealers clean and dry, keep the hose straight and check the connection each time you set up. For measured tubing, confirm the inner diameter with calipers or the fitting maker rather than by eye.

The step between 1/8 in and 5/32 in is small on the page and large in practice when the hose must grip a port. Once the size is right, length becomes a simple routing choice.

For a ready made line, confirm the fitting type before the length. A male quick connect that matches your pump saves cutting and joining, while a mismatch leaves you shopping for an adapter.

Measure the working distance first, since 18 in suits close setups and will feel short if the container sits farther away. For mixed size repair kits, plan the storage as well as the fit.

Six diameters and many connectors are handy for tracking down the right size, but they need clear labels so the next repair starts from a known point. For related bag care questions, read Can Really You Reuse Vacuum Sealer Bags? and What Exactly Are Vacuum Sealer Bags Made Of?.

The honest summary is that fit beats length every time. Choose the FoodSaver kit for jars, EVIL ENERGY for a known small diameter, LeLuv for a finished 1/4 in line and Purthog for size finding.

Our top 3 picks at a glance

  1. 1 FoodSaver Plastic Jar Sealer for Vacuum Sealer
    Best for Mason jar sealing

    FoodSaver Plastic Jar Sealer for Vacuum Sealer

    9.7/10 our score

    See it on Amazon
  2. 2 EVIL ENERGY 1/8" Silicone Vacuum Tubing Hose
    Best for 1/8 in tubing

    EVIL ENERGY 1/8" Silicone Vacuum Tubing Hose

    9.6/10 our score

    See it on Amazon
  3. 3 EVIL ENERGY 5/32" Silicone Vacuum Tubing Hose
    Best for 5/32 in tubing

    EVIL ENERGY 5/32" Silicone Vacuum Tubing Hose

    9.4/10 our score

    See it on Amazon

Frequently asked questions

What is the best vacuum sealer hose for Mason jars?

The FoodSaver Plastic Jar Sealer is the best fit here for Mason jar storage because it includes regular and wide-mouth jar sealers plus an accessory hose. It is made for Mason-type jars, sauces, mustards and jams.

Check your jar mouth before choosing a different hose or adapter.

What size vacuum sealer hose do I need?

Measure the connector opening or identify the required inner diameter before buying. The EVIL ENERGY options are 1/8 in and 5/32 in inside diameter, while the LeLuv hose uses a 1/4 in inner diameter and male quick-connect fitting.

A close-looking size may still seal poorly.

Can I use an automotive vacuum hose with a food vacuum sealer?

Only use a hose when its material, size and connection suit your food-storage setup. The EVIL ENERGY hoses are described as FDA compliant food grade pure silicone, but their application information focuses on automotive vacuum lines.

Confirm the complete food-contact setup before use.

Is a longer vacuum sealer hose better?

A longer hose helps when the container or accessory sits farther from the vacuum sealer, but extra length can make routing harder. The EVIL ENERGY hoses are 10 ft long, while the LeLuv hose is 18 in.

Choose the shortest length that reaches comfortably after confirming the connector size.

What should I check before buying a replacement hose?

Check the hose's inner diameter, outside diameter, connector style, length and intended use. Also confirm whether the hose includes a fitting or arrives as plain tubing.

A kit such as Purthog includes several sizes and connectors, while EVIL ENERGY provides tubing without a vacuum sealer connector.